1/11/2024 0 Comments Installing vinyl lattice panelsAllow for the height of the lattice fenceįor lattice fences that are going to be part of a garden’s border, add 2 inches to their height. Lattice inches = Project space inches + 0.25 inches + Frame thickness inches – Frame width inches. If you really want to know how wide your frames will be, think of adding the measurement of the frame material itself as well as any dividers or caps at each corner. Allow for framesįrames can be a headache if you’re not careful. Leave around 0.25 inches on either side of the panel to accommodate for adverse weather conditions that can expand or contract your plastic lattice fence during usage. Then find panels that match your specifications or sections of plastic lattice to match these dimensions. To do this, measure your project and write down the W, H, and L measurements. If you’re interested in installing a new lattice fence, it’s worthwhile to cut the panels first. Make it easier to work with by using some lightweight metal trimmers (tin snips) to cut these protruding nails first. When putting it in place, you may need to cut it at odd intervals with an electric saber saw which can in some cases damage the lattice if any nails stick out from the edge of your circular blade. Plastic lattice is a do-it-yourself landscaping solution that works great around trees, shrubs, and hedges. How do you keep vinyl lattice from buckling?.How do you attach plastic lattice to wood?.How do you cut lattice pastry without a lattice cutter?.What tool do you use to cut plastic lattice?.Allow for the height of the lattice fence.An alternative to using a vinyl blade is to flip a standard blade on the saw so that it rotates in the opposite direction, producing less stress on the vinyl lattice. These blades are expensive and produce less damage to the lattice while cutting. The best way to cut PVC lattice is to use a circular saw with a vinyl cutting blade. Sometimes the vinyl lattice will need to be cut to fit. Insert the fasteners approximately every 6 inches. Once the panels are properly aligned the fasteners can be installed around the perimeter of each panel. The reason for this is if adjustments need to be made to the panels, then only removing three screws allows the panel to be adjusted. This will hold the panels in place until they are all up. When installing the PVC panels, set them in place and insert only three screws along the top of each panel. Make sure that the panel is level both vertically and horizontally. The alignment of the first panel is critical. Deck screws are preferable because they do not require painting and are designed not to rust. The panels are installed by fastening them to the framework using staples or deck screws. ![]() If water-based paint is used as a primer, the chemicals in the pressure treated wood will leech through the final coat of paint. Always use an oil-based primer when painting pressure treated wood. The framework can be painted to blend or contrast with the PVC panels. The framework should be painted prior to installing the vinyl lattice fence panels. The top of the top rail should be mounted 4 feet above the ground. The bottom of the bottom rail should be mounted 6 to 12 inches from the ground. The frame requires top and bottom rails for mounting the vinyl fence panel. The framework of the fence is created by attaching 2 x 6 inch pressure treated rails between the posts using fence rail mounts (inexpensive hardware available at local hardware stores). The fence posts must be braced while the concrete is hardening, so they do not move. Both methods require the same concrete set-up time. Pour approximately two bags of powdered concrete into each hole, and thoroughly soak each hole with water. The second method is much easier and less expensive. If it is a large job, another option is to hire a cement truck to bring pre-mixed concrete to the jobsite. The cement is mixed by hand in a wheel barrow, and poured into each post hole. The cement can be poured directly into the post hole as a premixed liquid. There are two methods for cementing the post holes. Install the posts so that 5 feet of post is exposed above ground when finished. Most installers use a string level to ensure the straightness of the fence line during this process. The post holes should be dug in-line and spaced at 8 foot intervals. Post holes can be dug by hand or by using a gas powered post-hole digger. ![]() The deeper the post hole, the stronger the fence. Depending on wind load requirements and local soil conditions, post-hole depths can range from 18 to 36 inches. 4 x 4 inch pressure treated posts, cemented into the ground, create a stable base. Vinyl lattice fencing requires a foundation on which the framework is mounted.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |